Plumbing 101: A Guide to Installing a Bathtub
Plumbing 101: A Guide to Installing a Bathtub
Blog Article
They are making a number of good pointers regarding A Step-by-Step Guide to Installing a Bathtub in general in this post just below.
:max_bytes(150000):strip_icc()/adhesive-type-tub-and-shower-surround-2718959-hero-22d394dc48de474a988eeaad88e9d7b0.jpg)
Mounting a bathtub isn't precisely brain surgery, but it does need strong plumbing, carpentry, as well as occasionally, tiling skills. Changing an old bath tub with a new one is additionally a reasonably hard job. If the old tub is easily obtainable, the task can relocate quickly; if you need to open up a wall surface to get rid of the old tub and place the brand-new bath tub, the task is much harder. In either instance, the job is within a residence handyman's skills, although you will certainly require an assistant to vacate the old tub as well as set in the brand-new one. See to it you have actually certified yourself for the work and also fit attempting it. Rather than working with a contractor to take control of a halfway-completed task, it is much better to think about using one prior to you start. Chances are you might need an expert plumber to make tube connections.
This post will help you mount a new bath tub in your shower room if you have currently acquired a brand-new tub and also don't require to change the plan of your previous water supply pipes.
Your devices and material list should make up the following:
Preparing for the Setup
To start with, the sustaining frame supplied with the bath ought to be fitted (if needed) according to the supplier's directions. Next, fit the taps or mixer to the bath tub. When fitting the tap block, it is necessary to make certain that if the tap features a plastic washer, it is fitted between the bathroom and also the faucets. On a plastic bathroom, it is also practical to fit a supporting plate under the faucets system to avoid pressure on the bathtub.
Fit the versatile faucet ports to the bottom of the two faucets using 2 nuts and also olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet via the hole in the bathroom. Utilize the nut provided by the producer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. Ensure you utilize all of the supplied washers.
Attach the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bathroom ought to currently prepare to be fitted in its last position.
Removing Old Touches
If you require to replace old faucets with new ones as a part of your installment, then the first thing you must do is detach the water supply. After doing so, switch on the faucets to drain pipes any type of water remaining in the system. The procedure of eliminating the existing taps can be fairly problematic due to the limited accessibility that is frequently the instance.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that links the supply pipes to the taps. Have a fabric ready for the staying water that will certainly come from the pipes. As soon as the supply pipelines have been gotten rid of, make use of the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to stop the solitary faucets from turning throughout this process. When the faucets have actually been removed, the holes in the bath/basin will certainly need to be cleaned up of any old sealing compound.
Prior to moving on to fit the new faucets, contrast the pipeline connections on the old faucets to the new taps. If the old faucets are longer than the brand-new taps, then a shank adapter is needed for the brand-new faucets to fit.
Installing the Bath tub
Using the two wood boards under its feet, position the tub in the called for position. The wooden boards are handy in evenly spreading out the weight of the bath tub over the location of the boards instead of focusing all the weight onto four little factors.
The next goal is to guarantee that the bathtub is leveled all round. This can be achieved by checking the spirit level and adjusting the feet on the bathtub until the level reviews degree.
To set up taps, fit the bottom of the outermost versatile tap connector to the proper supply pipe by making a compression join; after that do the very same for the other tap.
Activate the water supply and also check all joints and brand-new pipework for leaks and also tighten them if needed. Fill the bath tub and additionally check the overflow electrical outlet and also the regular outlet for leaks.
Finally, deal with the bathroom paneling as explained in the manufacturer's user's manual. Tiling and sealing around the bath tub should wait until the tub has actually been used a minimum of when as this will certainly settle it into its last placement.
Fitting New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly need a plastic connector to avoid damage to the thread. One end of the connector fits on the plastic tail of the faucet and also the various other end supplies a connection to the existing supply pipes.
If you need to fit a monobloc, after that you will certainly need minimizing couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next, place the faucet in the mounting opening in the bath/basin making certain that the washing machines are in place in between the faucet and the sink. Safeguard the tap in position with the maker provided backnut. As soon as the faucet is securely in position, the supply pipes can be attached to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with normal tap adapters. The former type must be attached to the tap ends first, tightening just by hand. The supply pipelines can later on be connected to the other end. Tighten up both ends with a spanner after both ends have been linked.
Tiling Around the Tub
In the area where the bathroom meets the ceramic tile, it is essential to secure the accompanies a silicone rubber caulking. This is essential as the installation can relocate sufficient to fracture an inflexible seal, creating the water to pass through the wall surface in between the bath and also the tiling, leading to difficulties with dampness and feasible leakages to the ceiling below.
You can choose from a variety of coloured sealers to blend in your fixtures and installations. They are offered in tubes and cartridges, and also are capable of securing spaces up to a size of 3mm (1/8 inch). If you have a larger space to fill, you can load it with spins of soaked newspaper or soft rope. Bear in mind to always load the bathtub with water prior to securing, to allow for the motion experienced when the bathtub remains in use. The sealant can fracture relatively very early if you do not take into consideration this movement before sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are also quickly readily available on the market. It is recommended to fit the floor tiles making use of water-resistant or water resistant adhesive as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
:max_bytes(150000):strip_icc()/installing-a-tub-or-shower-surround-2718986-01-b02d6683a8ee4621bf9b9ac7ab0b1dd2.jpg)
We hope you enjoyed our piece on How to Install a Bathtub. Many thanks for taking the time to read through our post. If you please take the time to share this post if you enjoyed reading it. I cherish reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Instant fix? Dial! Report this page